Creativity cannot be tamed and the use of Bead Roller to make wrapper beads is a living proof to this factor. The do it yourself techniques known to many as DIY emerged years ago but have come to a lot of peoples attention in the recent years all thanks to the sudden boom in the use of social media which created open platforms to share and learn on various DIYs. The article below describes more on Paper bead roller.
For one to excel in paper pellet rolling there are no particular by book rules to follow but it is mainly a skill that revolves around creativity and imagination for successful execution of the project. To make the beads a beads roller is required and one can purchase an already made one or can also make one for themselves through DIY.
The first step to follow is to cut all the papers and trim them as per the type of pellet you wish to make. With the right knowledge, one can easily know what shape of beads you would wish to make and this decision is made while one keeps in mind the type of jewellery they wish to make, the size and also the pellet pattern that will please them best.
The next step is to now start the rolling and first to be placed on the pill roller is the wide side and slowly the rolling progresses. This is a process that should be conducted with no hurry as it is here if one is not careful enough they can ruin the entire thing. These are very light materials and hence one should be really tender with them.
When rolling commences have a tight grip on both the paper and the roller and do not loosen it whatsoever up until you are almost at the end. When 2 inches away from the end, then you can loosen and adjust the pellet into the shape you desire while avoiding any folding of the papers and riding off any undone ends.
While the wrapper has now acquired the shape you had envisioned, it is now the time to close it and move on to the next bead and here is when the wrapper glue is applied. Avoid the mistake of applying too much glue on the wrapper and leaving a bumpy and very hard to dry layer that can ruin your entire work.
At this stage the work is almost all done as the final stages will mainly involve reaching a fine end product and developing a pleasing and presentable final product. Finishing takes up most of the time as it is here the glue has to be well leveled and all ends should be fine. It is advised to apply a final thin layer on the bead for durability.
This, as said earlier is not a by rule project to do but one that requires creativity alone. After finishing all of the processes one can even opt to use a desired colour on the jewels to finish then fully and give them a beautiful appearance.
For one to excel in paper pellet rolling there are no particular by book rules to follow but it is mainly a skill that revolves around creativity and imagination for successful execution of the project. To make the beads a beads roller is required and one can purchase an already made one or can also make one for themselves through DIY.
The first step to follow is to cut all the papers and trim them as per the type of pellet you wish to make. With the right knowledge, one can easily know what shape of beads you would wish to make and this decision is made while one keeps in mind the type of jewellery they wish to make, the size and also the pellet pattern that will please them best.
The next step is to now start the rolling and first to be placed on the pill roller is the wide side and slowly the rolling progresses. This is a process that should be conducted with no hurry as it is here if one is not careful enough they can ruin the entire thing. These are very light materials and hence one should be really tender with them.
When rolling commences have a tight grip on both the paper and the roller and do not loosen it whatsoever up until you are almost at the end. When 2 inches away from the end, then you can loosen and adjust the pellet into the shape you desire while avoiding any folding of the papers and riding off any undone ends.
While the wrapper has now acquired the shape you had envisioned, it is now the time to close it and move on to the next bead and here is when the wrapper glue is applied. Avoid the mistake of applying too much glue on the wrapper and leaving a bumpy and very hard to dry layer that can ruin your entire work.
At this stage the work is almost all done as the final stages will mainly involve reaching a fine end product and developing a pleasing and presentable final product. Finishing takes up most of the time as it is here the glue has to be well leveled and all ends should be fine. It is advised to apply a final thin layer on the bead for durability.
This, as said earlier is not a by rule project to do but one that requires creativity alone. After finishing all of the processes one can even opt to use a desired colour on the jewels to finish then fully and give them a beautiful appearance.
About the Author:
If you'd like to buy a low priced paper bead roller you can search locally or online. We highly recommend this website at http://www.paperbeadgirl.com for all your bead making needs.
ليست هناك تعليقات:
إرسال تعليق